Friday, October 7, 2011

Book Snowman


Summers over (thank goodness) and now I'm in a crafty mood again!

I found this book pumpkin tutorial on pinterest from Craftberry Bush and promptly headed to pick up some books with my mom so we could try it out.

It ended up that I enjoyed it much more than her.

I made my first three, boy did my hand hurt after that!
IMG_0657

Then my neighbor asked me to make her some and gave me two books. I whipped out the dremel for those!
IMG_0659IMG_0661
And even with the burnt edges they looked super cute.

I also made mini ones!
IMG_0663

I then had the idea to make trees...
IMG_0687


and finally, today while browsing pinterest and seeing them over and over I had the idea of a snowman!


Book Snowman

Materials:
  • book (more pages=fuller end result)
  • scissors
  • card board
  • xacto knife (possibly a box cutter)
  • glue gun (or other glue if you're more patient - I am not.)
  • stick/dowel
  • white paint + water
  • paint brush
  • scrap paper for had
  • scrap fabric for scarf
  • tiny piece of paper for nose
  • buttons

First you'll cut out your snowman shape, I used to circular things and traced half of them onto the cardboard, then cut it out

Remove the cover of the book and hold the cardboard near the spine and trace with your xacto knife
(Update: I made a 2nd snowman and cut the bottom of the cardboard template flat and put that against the bottom of the book, so when you cut you're only cutting into the spine of the book once, leaving a flat bottom)
IMG_0755
IMG_0756

After I've got through a few pages I remove the cardboard and just use the lines I've already made.
IMG_0757

When you get a good amount of your knife in there you'll be able to remove some of the excess.
IMG_0758
IMG_0759

Keep going!
IMG_0762IMG_0763

It can start to get harder because the previously cut stuff getting in your way.
IMG_0767

So I move some of it over (being careful not to fold too hard and snap the spine)
IMG_0770

almost there!
IMG_0771

The cutting is done! Now youll want to go through and crease the spine so that itll flare out nicely. Youll then notice that the front and the back of the book doesnt match!
IMG_0773

Thats OK, its the back of the snowman anyway.

Now for the assembly

If your books spine has weak spots and is splitting like this:
IMG_0775

you can run a line of glue down the inside and hold it closed til dry (this is why I use the hot glue gun)
IMG_0776IMG_0777

One thing I hadn't thought about until I was done was that I didn't make the bottom flat! So I corrected that (this was my first snowman so you get to see my mistakes too)
IMG_0778

Now for the paint...
I wandered around my house for a while because I don't actually have paint. I used food coloring for the pumpkins and trees.

Then *bing* I remembered my friend had left a whole gallon of white paint at my house for a project I helped him with (over a year ago!)

I put some in a container and mixed it with water. You want to paint to show, but not make the pages stick.
IMG_0779IMG_0780

I put quite a few layers on, fanning out the pages in between. (I didn't let them dry, just added to it)
IMG_0781

Time for the stick, this helps with support. When you bend the book around the stick it should just fit the stick.
Glue the spine and one of the pages.
IMG_0783

Now you'll notice the back has a lot of gapping. I use the same idea as before where I run some glue along the inside. This helps with the major gapping.
IMG_0785

Accessorizing!
I used two circles and a strip for the hat.
IMG_0787
(the hole in the big circle is so it fits through the stick - I did not glue the hat to the snowman)

I added eyes, buttons, and a nose... but still felt like something was missing...
IMG_0788

A scarf!
IMG_0789

And there he is folks!
IMG_0790

3 comments: